Solvay PAI AI-10 Torlon® PAI powders Polyimide-imide High-temperature adhesion promoter for non-stick coatings

Product Information

UL

TDS

MSDS

SGS

COA

Design guide

Processing guide

Torlon® AI-10 is a polyamideimide (PAI) powder developed for the performance coatings industry. As a liquid polymer solution, the resin is incorporated into the formulation of engineered coatings; often as the principal primer, binder, or high temperature adhesive component. As a powder, the resin is used in specialty composites and unique dry spray applications. Coatings based on the Torlon® AI-10 polymer yield durable, abrasion resistant, thermally stable films that do not exhibit unwanted thermoplastic properties. The resin has superior resistance to organic solvents and a wide array of other commercial and industrial chemicals. Outstanding tribological characteristics are afforded both by the resin as well as its unparalleled intra-coat adhesion to fluoropolymers. Coatings based on AI-10 polymer have been shown to be cost effective in electrical/electronic, high temperature decorative and corrosion preventative applications. Magnet wire insulation and protective coatings for printed circuit boards are some of the electrical uses. Industrial applications include primers and decorative topcoats for cookware, appliances and housewares. AI-10 polymer has been combined with fluoropolymers to produce high-performance, low-friction, corrosion-resistant coatings that provide protection to saw blades, gears, carburetor needles and lawn and garden tools. Torlon AI-10 is also used for high-strength, high-temperature adhesives. Excellent bond strengths have been observed with stainless steel, aluminum and titanium alloys and polyimide films. A special grade (called AI-10 LM) has been developed to reduce the amount of residual methylene dianline (MDA) monomer to below the 1000ppm level specified in hazard communication regulations. A water soluable analogue of AI-10 (called Torlon® AI-30) is also available.

Torlon® polyamide-imide (PAI) is the highest performing, melt-processable thermoplastic. The amorphous polymer has exceptional resistance to wear, creep and chemicals and performs well under severe service conditions up to 260°C (500°F). Torlon® PAI also has superior electrical and structural characteristics at high temperatures, an extremely low coefficient of linear thermal expansion, and exceptional dimensional stability. Typical applications include non-lubricating bearings, seals, valves, compressors, and piston parts, bearing cages, bushings, and thrust washers.Parts made from Torlon® PAI polymers perform under conditions generally considered too severe for thermoplastics. Typical applications include aircraft hardware and fasteners, automotive transmission and powertrain components, and oil & gas exploration and recovery equipment. The material’s excellent electrical insulating properties have made it a common choice for semiconductor fabrication and testing as well as electrical and electronic components.Polyamide-imide (PAI) powders are widely used in high-performance, non-stick, and corrosion-resistant coatings for a variety of other demanding industrial uses.

Torlon® PAI is virtually unaffected by aliphatic and aromatic hydrocarbons, chlorinated and fluorinated hydrocarbons, and most acids at moderate temperatures. The polymer, however, may be attacked by saturated steam, strong bases, and some high-temperature acid systems. Proper post-cure of Torlon® PAI parts is necessary to achieve optimal chemical resistance.Like other high-temperature engineering resins and composites, Torlon® PAI parts absorb water, but the rate is slow and parts can be rapidly restored to original dimensions and properties by drying.Of particular interest to aerospace and automotive engineers is the ability of a polymer to maintain its properties after exposure to commonly used fluids. Total immersion tests show Torlon® PAI is not affected by aircraft hydraulic fluid at low temperatures or by common lubricating fluids and turbine oil, even under stress at elevated temperatures.

Torlon® PAI Product grades:

Wear-resistant grades 

High-strength grades

Polyamide-imide (PAI) powders

Torlon® PAI Model Number:

Pellets

Torlon® PAI 4203

Torlon® PAI 4275

Torlon® PAI 4301

Torlon® PAI 4435

Torlon® PAI 4601

Torlon® PAI 4630

Torlon® PAI 4645

Torlon® PAI 5030

Torlon® PAI 7130

powders

Torlon® PAI AI-10

Torlon® PAI AI-10LM

Torlon® PAI AI-30LM

Torlon® PAI 4000T

Torlon® PAI 4000TF

Torlon® PAI 4200

Suzhou YingJinbao Plasticizing Co., Ltd. was established in 2015, located at 8-3-12 Huadonguoji, Taicang City, Suzhou City, Jiangsu Province, China. We sell all kinds of plastic raw materials, including PAI plastic, PEEK plastic, PFA plastic, ECTFE plastic, PVDF plastic, PTFE plastic, and other special engineering plastic raw materials. We also offer TPEE plastic, EVA plastic, EAA plastic, TPU plastic, TIE adhesive resin plastic, and other elastomer plastic raw materials. Additionally, we provide PVDC plastic, EVOH plastic, and other high gas barrier materials.

We have a modification factory that can be customization products according to your specific requirements and offer a wide range of color options to meet your demand.With mutual benefit and win-win cooperation, we guarantee to provide the best quality products at the best price. No matter which region or country you come from, Suzhou YingJinbao will be your long-term and stable strategic partner.